Orion-system VCM-X/RNE Controller Manual de usuario descargar pdf (Pagina 72)

Zone

VAV/ZONE CONTROLLER PROGRAMMING

VCM-X / RNE Operator Interface SD

VAV/Zone Setpoint Screens

Setpoint Screen #13 - Zone Alarm Delay

XX Box Spts IDXXXX

Zone Alarm Delay

Must Be Out Of

Limits For.: XXX Min

As mentioned above, if you conﬁ gure the controller to generate zone

temperature alarms, this is the amount of time after the box goes into the

Occupied Mode that the temperature must be outside the alarm limits

before an alarm is generated.

Description Minimum Default Maximum

Out of Limits 1 Min 30 Min 300 Min

Setpoint Screen #14 - Day/Night Schedule

XX Box Spts IDXXXX

Day/Night Schedule

Control #: X

0=AHU 1-5=Scheduler

This screen allows you to set the VAV/Zone Controller to operate on a

remote schedule instead of the schedule that is contained in the VCM-X

or RNE Controller. Enter <0> to operate on the AHU schedule. Enter <1-

5> to use an external schedule. A GPC Plus is required for schedules 1-5.

Description Minimum Default Maximum

Schedule Control Number 0 0 1 to 5

Setpoint Screen #15 - Maximum Slide Offset

XX Box Spts IDXXXX

Maximum Slide Offset

Effect on Spt.: XºF

If the Flush Mount Wall Sensor has the optional Setpoint Slide Adjust,

this is the maximum amount you can adjust the heating and cooling

setpoints up or down as the slide is moved from the center position to

its full up or down position.

Description Minimum Default Maximum

Effect on SP 0ºF 0ºF 6ºF

Setpoint Screen #16 - Push-Button Override

Duration

XX Box Spts IDXXXX

Push-Button Override

Duration : X.X Hr

If the Flush Mount Wall Sensor has the optional Push-Button Over-

ride, this is the amount of the VAV/Zone Controller will resume using

its Occupied Setpoints during unoccupied mode. This will generate a

call for the Air Handler to start its fan and provide heating or cooling,

depending on how you conﬁ gure the Air Handler.

Description Minimum Default Maximum

Duration 0.0 Hr 0.0 Hr 8.0 Hr

Setpoint Screen #17 - Maximum EMS Offset

XX Box Spts IDXXXX

Maximum EMS Setpoint

Offset...: XXºF

If the Energy Management System (EMS) is activated, the heat and cool

setpoints can be spread apart by this amount.

Description Minimum Default Maximum

Maximum EMS Setpoint

Offset

0ºF 0ºF 30ºF

Setpoint Screen #18 - Sensor Calibration for

Space Temp and Supply Air Temp

Sensor Calibration

SPC: XXX.Xº XXX.Xº

SAT: XXX.Xº XXX.Xº

[SAT Only if Sensor]

The Thermistor Type III sensor readings can be calibrated. Enter a

Positive value to increase a reading and a Negative value to decrease

a reading.

NOTE: The Supply Air Temperature calibration offset only oper-

ates on the reading when the VAV/Zone Controller has

its own Supply Air Temperature sensor installed on the

AUX2 input. If the supply temperature is received from

a global broadcast, you will need to go to the air handler

to calibrate the temperature reading.

Description Minimum Default Maximum

SPC (Space Temp) -100ºF 0ºF +100ºF

SAT (Supply Air) -100ºF 0ºF +100ºF

1 2 ... 67 68 69 70 71 72 73 74 75 76 77 ... 91 92

Comentarios a estos manuales

Sin comentarios

Orion-system VCM-X/RNE Controller Manual de usuario Pagina 72

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Orion-system VCM-X/RNE Controller