Orion-system VCM-X/RNE Controller Manual de usuario Pagina 25
- Pagina / 92
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
VCM-X / RNE Operator Interface SD
VCM-X CONFIGURATION
25
Confi guration Screens
In order to correctly set up the VCM-X Controller, you must fi rst con-
fi gure several parameters in regard to the type of HVAC unit and system
you have installed. Most of these values and operating parameters are
only set once at the initial system setup and are never changed.
Modular Service Tool SD Instructions
No matter what screen or menu you’re in, press <CONFIGURATION>.
The Unit Selection Screen will appear, shown below, requesting that you
enter the unit ID number.
Unit Selection
Enter Unit ID#
Selected ID#: XXXX
*00*
Enter the correct unit ID number of the VCM-X Controller you want to
confi gure and then press <ENTER>. You must type in the number, even
if it is “1”. Once communication is established, the *00* at the bottom
will disappear. Then
press <>. You will then see Unit Confi guration
Screen #1. Press
<ENTER> to save entered data and press <> to
scroll through the screens.
NOTE: If the *00* remains, it indicates a communication failure
to the controller.
System Manager SD Instructions
From any Main screen, press <SETPOINTS>. The screen below will
appear because this option requires passcode clearance. Only a Level 2
passcode can change setpoints.
THIS ACTION REQUIRES
PASSCODE CLEARANCE
Enter Passcode: XXXX
If the correct passcode was entered, the Unit Selection Screen will be
displayed.
Unit Selection *00*
Enter Unit ID#
Selected ID#: XXXX
Enter the Unit ID of the controller you wish to change schedules for
and press <ENTER>. You must type in the number, even if it is “1”.
Once communication is established, the *00* at the top will disappear.
Then
press <>.
NOTE: If the *00* remains, it indicates a communication
failure to the controller.
The following screen will be displayed:
Change Setpoints
Configure Unit
Save/Copy/Restore
Scroll down to the ‘Confi gure Unit’ option and press <ENTER>. This
will take you to the fi rst Confi guration Screen shown below.
Confi guration Screen #1 - Duct Static
Pressure
VCM-X Cnfg ID 59
Duct Static Pressure
Control: YES
Use < Or > To Change
If the HVAC unit has a Supply Fan that delivers a Constant Volume
of air, select NO. If the HVAC unit has a Supply Fan that delivers a
Variable Volume of Air using a VFD or a Bypass Damper, select YES.
Default is YES.
Confi guration Screen #2 - Supply Fan Cycle
VCM-X Cnfg ID 59
Supply Fan Cycle
Mode: NO
Use < Or > To Change
If you want the HVAC unit’s Supply Fan to run during Heating, Cool-
ing, or Dehumidifi cation Modes, select YES. If you want the HVAC
unit’s Supply Fan to run continuously while in the Occupied Mode,
regardless of the Heating, Cooling, or Dehumidifi cation Modes, select
NO. Default is NO.
VCM-X Confi guration Screens
- VCM-X / RNE Controller 1
- Operator Interface SD 1
- Technical Guide 1
- SD CARD UPDATING INSTRUCTIONS 2
- IMPORTANT NOTICE 2
- SYSTEM CONNECTION 4
- Modular Service Tool SD 4
- Modular System Manager SD 6
- Back View 7
- Power/Comm Board Wiring 8
- Stand Alone Connection 9
- MODULAR SERVICE TOOL SD 10
- Modular Service Tool Keys 10
- Setup Screens 11
- Programming the Time 11
- Programming the Date 11
- Alarm and Override Search 13
- Schedules and Holidays 14
- Holiday Start/Stop Times 15
- Schedule Override 15
- SYSTEM MANAGER SD 16
- Setting the Operating Mode 18
- Changing Passcodes 19
- Holiday Start/Stop Times 23
- VCM-X CONFIGURATION 24
- VCM-X CONFIGURATION 25
- VCM-X Confi guration Screens 25
- RNE CONFIGURATION 34
- RNE CONFIGURATION 35
- RNE Confi guration Screens 35
- VCM-X / RNE SETPOINTS 44
- VCM-X / RNE Setpoint Screens 45
- VCM-X / RNE STATUS 56
- VCM-X / RNE Status Screens 56
- > 65
- > to 65
- VAV Zone Confi guration 66
- <0> if you 67
- <0> 67
- Separate Loop 68
- VAV/Zone Setpoint Screens 69
- VAV/ZONE CONTROLLER STATUS 73
- VAV/Zone Status Screens 73
- VAV/ZONE CONTROLLER STATUS 74
- VAV/Zone Damper Force Modes 75
- MINILINK PD STATUS 76
- MINILINK PD PROGRAMMING 77
- TROUBLESHOOTING 78
- VCM-X / RNE Outputs Force 78
- Saving Setpoints 80
- SD Memory Card Update 82
- WattMaster Controllers 83
- E-BUS Modules 84
- Setpoints.........45 86
- VAV/Zone.........71 86
- Setpoint.........52 88
- VAV/Zone Status.........72 89
Relacionado con productos y manuales para Hardware Orion-system VCM-X/RNE Controller
Hardware Orion-system VCM Manual de usuario
(52 paginas)
(52 paginas)
Hardware Orion-system PT-Link-LON Manual de usuario
(40 paginas)
(40 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales