Orion-system VCC-X Controller Manual de usuario Pagina 31
- Pagina / 96
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
VCC-X Operator Interface SD
VCC-X CONFIGURATION
31
VCC-X Confi guration Screens
Confi guration Screen #33 - Economizer
Voltage Output
VCC-X Cnfg ID #
Econo Voltage Output
Min Volts: 2.0VDC
Max Volts: 10.0VDC
Enter a value between 0.0 and 10.0 VDC for the Economizer mini-
mum and maximum output voltage. Defaults are 2 VDC Min and
10 VDC Max.
Description Minimum Default Maximum
Min Economizer Voltage 0 2 10
Max Economizer Voltage 0 10 10
Confi guration Screen #34 - CO
2
Sensor
Installed
VCC-X Cnfg ID #
CO2 Sensor Installed
NO
USE < or > TO CHANGE
Select YES if you have a CO
2
Sensor installed. Default is NO.
Confi guration Screen #35 - Building Pressure
Sensor Installed
VCC-X Cnfg ID #
Building Pr. Sensor
Installed
None
If this unit has a Building Pressure Sensor installed, select Analog if
it is a wired sensor. Select Receive Broadcast if the Building Pres-
sure Sensor is attached to a separate device that will broadcast the
reading, e.g., GPC-XP Controller. Default is None.
Confi guration Screen #36 - Building Pressure
Control
VCC-X Cnfg ID #
Building Pr. Control
None
USE < or > TO CHANGE
Default is None. Available options are:
None—No Building Pressure Control by this controller.
On/Off Exh Relay—If an On/Off Exhaust Fan is being
used, select this option and confi gure a relay output as
Exhaust Fan. If the building pressure rises above
setpoint, this relay will energize. This is Direct-Acting
control.
Modulating Exh—If the building pressure rises above
setpoint, a modulating signal will be used to control an
exhaust fan VFD or a modulating damper to maintain
setpoint. A relay confi gured as Exhaust Fan can be used
to enable this device so that the modulating signal can
control it. This is Direct Acting control.
OA Damper—Select if reverse acting Building Pressure
Control using the Outdoor Air Damper is required. If
the building pressure falls below setpoint, the OA
Damper (Economizer) signal will be used to modulate
the OA Damper to maintain setpoint. This is Reverse
Acting control.
Supply Fan—Contact WattMaster Factory regarding
this reverse acting Building Control option. This should
not be used in most applications. This is Reverse Acting
control.
Confi guration Screen #37 - Building Pressure
Control Rate
VCC-X Cnfg ID #
Building Pr. Control
Rate: 10 Sec
[ 1 - 30 Seconds ]
Default is 10 seconds. The Building Pressure Control Rate is the
time period between changes to the Building Pressure Control signal.
Confi guration Screen #38 - Building Pressure
Control Max Adjust
VCC-X Cnfg ID #
Building Pr. Control
Max Adjust: 5%
[ 1 - 30% ]
This is the maximum amount that the Building Pressure Control
output can adjust to when it needs to. Default is 5 percent.
- VCC-X Controller 1
- Operator Interface SD 1
- Technical Guide 1
- SD CARD UPDATING INSTRUCTIONS 2
- IMPORTANT NOTICE 2
- SYSTEM CONNECTION 4
- Modular Service Tool SD 4
- Modular Service Tool 5
- Modular System Manager SD 6
- Network Connection 7
- Power/Comm Board Wiring 8
- Stand Alone Connection 9
- MODULAR SERVICE TOOL SD 10
- Modular Service Tool Keys 10
- VCC-X Operator Interface SD 11
- Alarm and Override Search 13
- Schedules and Holidays 14
- MODULAR SYSTEM MANAGER SD 16
- MODULAR SYSTEM MANAGER SD 17
- Setting the Operating Mode 18
- Changing Passcodes 19
- VCC-X CONFIGURATION 24
- VCC-X CONFIGURATION 25
- VCC-X Confi guration Screens 25
- VCC-X Confi guration Screens 26
- VCC-X Setpoint Screens 39
- VCC-X SETPOINTS 40
- VCC-X SETPOINTS 41
- VCC-X STATUS 54
- VCC-X Status Screens 54
- RSMV CONFIGURATION 64
- RSMV Confi guration Screens 64
- RSMV STATUS 67
- RSMV Status Screens 67
- VAV/ZONE CONFIGURATION 69
- VAV/ZONE CONFIGURATION 70
- VAV/Zone Setpoint Screens 72
- VAV/ZONE STATUS 76
- VAV/Zone Status Screens 76
- VAV/ZONE DAMPER FORCE 78
- VAV/Zone Damper Force Modes 78
- MINILINK PD CONFIGURATION 80
- VCC-X Outputs Force 81
- TROUBLESHOOTING 82
- > to get to the Balance 83
- Save Setpoints - Network Mode 83
- SD Memory Card Update 85
- WattMaster Controllers 86
- HVAC Mode Deadband.........41 89
- VAV/Zone.........75 89
- Controlling Sensor Low Alarm 91
- VAV/Zone Confi guration 93
- VAV/Zone Status 93
- Zone Damper Position 94
Relacionado con productos y manuales para Hardware Orion-system VCC-X Controller
Hardware Orion-system VCM Manual de usuario
(52 paginas)
(52 paginas)
Hardware Orion-system PT-Link-LON Manual de usuario
(40 paginas)
(40 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales