Orion-system RNE Modular Controller Manual de usuario descargar pdf (Pagina 11)

RNE Modular Controller Field Technical Guide

OVERVIEW

Parts and Descriptions

PART NO. PART DESCRIPTION ILLUSTRATION PAGE NO.

OE415-02 IP Module Kit - Internet/LAN Connection

Used for Internet or Local Area Network communications with the control

system. Field installs by plugging into the CommLink IV circuit board and

provides an addressable Ethernet connection to the controls system from

any computer connected to your building’s LAN. It can also be conﬁ gured to

allow access to the control system from the Internet through your LAN if your

Ethernet ﬁ rewall is conﬁ gured for this option.

Includes: IP Link module, 10 ft. long Ethernet cable, and installation instruc-

tions. Prism 2 computer front-end software must be installed on the remote

computer in order to dial-up and communicate with the controls system.

See the IP

Module

Technical

Guide

OE366 USB-Link 2 Kit

The USB-Link 2 is a pocket-sized communications interface used to connect

a laptop computer to your controls system for programming and monitoring

purposes, utilizing a modular cable to allow connection to the service port

connector on the controllers and a USB cable to connect to a laptop com-

puter.

Includes: USB-Link 2 for multiple or single loop systems, USB cable, modular

connection cable, two mini-DIN to terminal adapters, and Prism 2 software.

See the

USB-Link 2

Technical

Guide

OE364-22 MiniLink Polling Device

Control enclosure is for indoor use only. Used with all Orion controllers to

provide network communications, zone voting, alarming, and tenant logging

capabilities. A MiniLink Polling Device is required on each loop of a Net-

worked system. Includes: MiniLink Polling Device mounted in the EE000075-

01 control enclosure. Control Enclosure cover is shown removed in picture.

EPROM

RAM

CX2

CX3

CX4

YS101818P552

PROCESSORPBOARD

CX5

CX1

CX6

WDOG

PHILIPS

0-10V

4-20mA

THERM

R27

R31

GND

24VAC

TB1

C11

U12

LED 2

POWER

R25

R26

CX15

CX13

PROC.

DRIVER

LOOP

DRIVER

LOCAL LOOP

GND

AIN 2

AIN 1

+5V

TB2

OFF=0-5V

AIN2

AIN

0-10V

4-20mA

THERM

SHLD

TB3

U15

LD5

LD6

U13

LED 1

RV1

VREF

CX2

U11

YS101900PMINILINK

POLLING

DEVICE

REV. 1

OFF

CX14

NETWORK

DRIVER

RN3

SHLD

TB4

U14

NETWORK

LOOP

ADD

R24

LD4

U10

RN2

SW1

R30

R29

R28

C10

CX6

CX1

CX7

See the

CommLink

IV Technical

Guide

OE365-15-

EBA

E-BUS Adapter Board

The E-BUS Adapter Board is used for connecting the EBTRON

, GreenTrol

or Paragon Airﬂ ow Measurement Digital Transmitter to the VCB-X Control

System. The E-BUS Adapter Board connects to the VCB-X Controller with an

EBC E-BUS cable. Cable supplied separately.

See

Page 39.

OE508 Prism 2 Front-End Computer Software

Prism 2 provides standard, easy to understand status screens for each

type of RNE equipment installed. Prism software has provisions for custom

screens which allow ﬂ oor plans, equipment photos, or user-deﬁ ned summary

screens to be implemented to meet their own individual needs. All controlling

setpoints, trend logs, and alarm conditions are accessed in the Prism environ-

ment. Prism can be conﬁ gured for direct on-site installation, remote modem

connection, or TCP/IP Internet connection to several installations.

See the

Prism 2

Technical

Guide

OE437-03 Communication Surge Protector Kit

Used to isolate power surges to the communications wiring caused by

lightning strikes for communications wiring loops that are routed outdoors or

between buildings. One kit is required at each point where the communica-

tions wiring leaves or enters a building.

Includes: Communication Bus Surge Protector, Base Module, and Mounting/

Wiring Instructions.

N/A

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 87 88

Comentarios a estos manuales

Sin comentarios

Orion-system RNE Modular Controller Manual de usuario Pagina 11

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Orion-system RNE Modular Controller