Orion-system VCM-X/RNE Operator Interfaces Manual de usuario descargar pdf (Pagina 66)

MINILINK PD PROGRAMMING

VCM-X / RNE Operator Interfaces Technical Guide

MiniLink PD Conﬁ guration Screens

MiniLink PD Conﬁ guration

In order to correctly setup the MiniLink PD, you must ﬁ rst conﬁ gure

several parameters in regard to the type of system and operating param-

eters for the system it is installed on. Most of these values and operating

parameters are only set once at the initial system setup and are never

changed.

System Manager Instructions

From any Menu Screen, press the <SETPOINTS> button. The Unit

Selection Screen will appear requesting that you enter the unit ID num-

ber. All MiniLink PDs are set at address 60. Enter the correct unit loop

number for the loop the MiniLink Polling Device is connected to (Loop

1 you would enter 1) and then enter

<60>. Press <ENTER>. You will

see the screen shown below.

1) Change Setpoint

2) Configure Unit

3) Damper Force

ESC) Exit Menu

Press <2> on the keypad to enter the ﬁ rst Unit Conﬁ guration Screen.

Modular Service Tool Instructions

From any Menu Screen, press the <CONFIGURATION> button. The

Unit Selection Screen will appear requesting that you enter the unit ID

number. Enter the correct unit ID number of the controller you want to

conﬁ gure and press

<ENTER>. You will then see Unit Conﬁ guration

Screen #1.

Conﬁ guration Screen #1 - System Type

Polling Unit Config

System Type

Selection: X

[0=Zoning 1=VAV]

This screen allows you to select whether you want the system to behave

as a VAV system or a Zoning System. If you select VAV, this will allow

tenant logging for your VAV system.

Conﬁ guration Screen #2 - Last Polled Zone

Polling Unit Config

Last Polled Zone

Address: XX

[Enter Last Zone]

This zone is the last zone on the local loop of your zoning system that

is to be included in zone voting.

Conﬁ guration Screen #3 - Mode Changeover

Time

Polling Unit Config

Mode Changeover Time

Minutes: XX

[Enter Period Time]

This is the amount of time that you want to allow between changeover

from heating to cooling modes.

Conﬁ guration Screen #4 - Optimal Start

Target Zone

Polling Unit Config

Optimal Start

Target Zone..: XXX

[Enter Target Zone]

This is the unit ID of the Zone that you want to be satisﬁ ed by the normally

scheduled start time. If you enter “-1” into this box, it will average all

zones instead of picking a speciﬁ c zone. If you do not require Optimal

Start, enter “0”.

Conﬁ guration Screen #5 - Maverick Testing

Polling Unit Config

Maverick Testing

Disabled: YES

[0=NO 1=YES]

Disabling the Maverick Testing allows known troubled zone(s) to con-

tinue voting without causing a Maverick alarm. In other words, all zones

are included in the voting regardless of whether they are more than four

degrees from setpoint.

Conﬁ guration Screens #6-65 - Alarm Polling

Polling Unit Config

Enable Alarm Polling

Unit XX : YES

[0=NO 1=YES]

Enabling Alarm Polling allows any alarm from the loop to be polled.

You must set this for each controller on the loop.

1 2 ... 61 62 63 64 65 66 67 68 69 70 71 ... 83 84

Comentarios a estos manuales

Sin comentarios

Orion-system VCM-X/RNE Operator Interfaces Manual de usuario Pagina 66

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Orion-system VCM-X/RNE Operator Interfaces